The Right Way To Discharge Capacitor In Switch Mode Power Supplies
Switch mode power supply contain some large filter capacitors that can hold dangerous charges even if the unit has not been used for several days. Typical values of this type of filter capacitor are 220uf 250volt and 330uf 400volt! If you are going to work on the power supply circuits, it's a good idea to discharge that capacitor first. There are three ways to discharge the big filter capacitor in a power supply. 1)Discharge it with a screw driver (not recommended). The reason for not using the screw driver to discharge a capacitor is because -the printed circuit board or circuitry can be damage due to the spark generated while discharging the high voltage capacitor.
I once blowed the power section using this method. However, if you know that the capacitor stored voltage is not too large, you can easily discharge it with a small screw driver. -if the capacitor holds a heavier charge of electricity. Discharging the capacitor may melt the tip of the screw driver and the copper on the printed circuit board. -Sometimes a heavier spark may cause small disintegrated solder lead or copper to fly out from the circuit board and may injured your eyes. 2)Place the leads of a socketed 100 watt electric bulb on the leads of the capacitor. This method had been used by many technicians around the world for the light bulb will act as an indicator to see if the capacitor still holds the charge. If there is a charge the light bulb will light and after discharged the light bulb will goes off. 3)Place the leads of a high wattage resistor on the leads of the capacitor.
I use a 2.2k ohm 10 watt resistor to discharge the high voltage capacitor in a switch mode power supplies. It is simple to use and very effective .It takes only couple of
seconds to fully discharge the capacitor. Conclusion I strongly suggest for those who use screw driver to discharge a capacitor to swift to the second and third method as these is the safest method to protect the circuit and most importantly is yourself. Jestine Yong is a electronic repairer and a writer. For more electronic repair information please visit his website at
http://www.noahtec.com/electronic-repair-articles.htm
Related News
|
 |
|
|
RELATED ARTICLES
Cheap Ink Cartridge
A cheap ink cartridge is sometimes the only way that people can afford to keep all of their printers ready for use. Internet email addresses are constantly loaded with a number of offers from various online merchants, but one such email that a consumer might not want to ignore is any one that offers a great deal on ink cartridges. Some of these deals can offer the consumer a substantial amount of savings on their ink cartridges for just about any printer. Buying a cheap ink cartridge is the perfect opportunity to have quality ink for your printer while enjoying savings that can be quite significant on a printer cartridge.
A Look Inside The Elusive Inkjet Industry
The Inkjet printer industry is booming. Office supply companies report they make more money on ink sales alone than on printer sales overall. Due to increasing ink sales, many inkjet manufacturers have introduced innovative products and services to meet the demands of discerning consumers. Customers are now able to purchase refill kits that allow them to handle their inkjet needs at home, without having to purchase expensive new cartridges. Refill kits contain a syringe like instrument that injects ink into the cartridge.
The Making of Energy Efficient Datacenters
The Crooked E: The Unshredded Truth About Enron is a wonderful movie to watch. It is based on the book, The anatomy of greed, written by a former employee of Enron, Brian Cruver. One interesting thing that comes on our minds is the size of all power companies. They are all huge. We all depend on power for just about everything and yet very rarely do we think about conserving energy. A typical PC for example takes about 135 watts of power. A data center with about a 1000 servers should typically take about 135 x 1000 Watts or 135 Kilowatts and that would just power the computers. This does not include the air-conditioning and lighting. According to to a research paper sponsored by The California Energy Commission in a datacenter about 50% of the total energy consumed is by the servers and
about 35% is the air conditioners.
Here are some interesting research done in this field -
Feeling the heat- An interesting paper by Liebert describing the challenge
of effectively managing the heat dissipation in datacenters.
Heat-Density Trends in Data Processing, Computer Systems, and Telecommunications
Equipment- This white paper provides valuable
current data and best available insights regarding historical and
projected trends in power consumption and the resulting heat
dissipation in computer and data processing systems (servers and
workstations), storage systems, and central office-type
telecommunications equipment.
This problem can be solved by making better energy efficient air
conditioners and by making more energy
efficient computers. Many companies have taken a lot of interest
in subject. However, nothing substantial has been done primarily
because of the market requirements. The end users still want to host
their sites on the fastest processors which drives the market with the
latest processors. Going at this rate we would reach a time soon when
the energy required would be much higher than the energy available in
the market.
Intel, AMD, Transmeta and Via have all released processors which
consume very low power. A typical Pentium or AMD processor consumes
about 25 Watts of power, whereas these low powered processors take only
about 5 watts of power i.e. about 5 low powered processors would
consume as much power as a single main stream processor of today. These
low powered processors are also generally fan less processors which
means lower noise levels too. Intel has the centrino which has a lower
power consumption than the regular pentiums. Intel also has the arm
processors but those are RISC. Our prime focus would be AMD, Transmeta
and Via. They all have some very promising products.
One thing to be noted is that most of these low powered processors work
only at about 1.2GHz or lower. So they won't be as fast the pentium4s.
Which means one would have to host lesser sites per server. A good
recommendation would be upto a maximum of 600 sites on a
regular pentium 4 server. A low powered processor should comfortably
take about 200 sites. One advantage of these low powered processors is
that they have a very small form factor too. This means that one can
have more such servers in the same space that is typically allocated to
a high powered servers. All datacenters use a profitability matrix
based on the following rule: Performance/Per
Watt/Per Cubic Foot. This is one place where the low powered
processors really score high.
AMD Geode? NX Processor family
comprises of the AMD Geode? NX 1250@6W processor, the AMD Geode?
NX 1500@6W processor and the AMD Geode? NX 1750@14W processor. The
first two in these consume only 6Watts of power and run without a
cooling fan. According to AMD they provide the highest x86 performance
for fan less operations. They are based on the mobile AMD Athlon
processor technology.
Transmeta was one of the first companies to develop low powered processors.
For a long time Transmeta was known as the company where the
Microsoft co founder Paul Allen had interests in and the place
where Linus Trovalds, the father Linux, worked. Both of them are no
longer part of the organization. Today they are known for the two
processor families they have - The transmeta crusoe and
the transmeta
efficeon
Transmeta Crusoe?-
processors range from 500Mhz to 1.2 Ghz. According to Transmeta,Crusoe is a unique combination
of software and hardware. It's this radical design that gives Crusoe its
important advantages, and manufacturers of all kinds of electronic
devices their first truly innovative new platform in over 25 years.
Thanks to Crusoe, mobile devices can be made smaller and lighter than
ever. These new devices will be more comfortable to use, too, because
Crusoe generates very little heat a problem that plagues the industry's
legacy hardware-only processors. And because it uses far less power,
mobile devices running on Crusoe run far longer on a single battery
charge, and Crusoe-powered ultra-dense servers do far more work per
watt, far more efficiently.
Transmeta
Efficeon processors are the higher end processors from Transmeta
and they run at upto 1.6Ghz and have high performance I/O interfaces.
They are built upon Fujitsu's next-generation 90nm silicon technology
featuring transistors with a length of just 40nm.
The entire Transmeta range not just uses the x86 instruction set, they
also have full multimedia instruction support (MMX, SSE-SSE2).
Transmeta has done very little in marketing in terms of selling their
products for the server market. Like all other companies they have
focussed on mobile products, set-top boxes etc.. While these products
are
great for the mobile market, they do have a great potential in the
server market. FIC, JM-Net etc. have some products for the server
market
which run on the Transmeta processors.
Via, the Taiwanese
manufacturer
purchased the Cyrix processors and has since gotten out of the race of
faster processors with AMD and Intel. Instead they are focussing on fan
less, low-powered processors. They have the Eden and the C3 range of
processors. The power consumption varies from only 7watts to
15Watts. Additionally, the processors come with the
PadLock Hardware Security Suite which provides a platform approach to
computer security, ensuring uncompromising security performance. These
features include the implementation of the Quantum-based VIA PadLock
RNG (Random Number Generator), and the VIA PadLock ACE (Advanced
Cryptography Engine) supporting AES encryption.
According to Via, the VIA Eden-N
Processor is the world's smallest, lowest power and most secure
native x86 processor. It is a mere 15mm x 15mm in terms of size and
consumes between 2.5W @ 533MHz to 7W @ 1GHz.
Via again like Transmeta has not focussed in the server market. The
images above give a good idea of the benefits of this processor in the
server market. For datacenters, Via may be the best in the
Performance/Per Watt/Per Cubic Foot matrix.
Companies like Hitachi make some very good low powered hard disk drives
which have a very small form factor. They have both IDE's at 7200 rpm
as well as SCSI hard drives.
Many may think it is better to take higher end servers as the power or
heating problem does not directly affect them. As mentioned earlier a
server driven by a low-powered processor would be able to take just
about 200 sites. This means that a person with 600 sites would need to
take 3 such servers instead of one higher powered server. Here are some
benefits of this scenario.
One of the biggest factors influencing the performance of sites on the
internet is the capability of the network card (ethernet) .
When all sites are
hosted on just one server, they all would use the same network
card to push the data. Now if these sites are distributed among 3
servers the amount of data that the sites can push would be 3 times
more
which means faster access to the sites. Another benefit is that if one
of the site goes down all 600 people would not be effected, rather only
1/3rd the number of sites would be affected.
Hence, the number of support request would be lesser. And finally, such
processors are very affordable. Typically they would be just a third of
the cost of regular mainstream processors.
A Look at Laser Toners
Laser toner is the ink for laser printers. It is an extremely fine synthetic powder (usually plastic) packed into a cartridge. You insert the cartridge into your laser printer according to the manufacturer's instructions. When the printer goes to print a page, there are several steps to the process:
Two Essential Accessories For Notebook Computers
A Good Notebook Bag
How to Choose a New Hard Drive for Your Computer
If you are running out of space on your computer or find that programs load a little slow, or that big files take a long time to open, it may be time for a new hard drive.
A Guide to Refurbished Laptops
Computing freedom, independence, and mobility don't have to come with a hefty price tag.
Electronic Schematics Diagram-The Four Commonly Asked Questions
I came across quite a number of questions about electronic circuit schematics diagram.
Printer Cartridges - Step Back in History
You are working and trying to print out important documents when you discover that you are out of ink. This would have been a big drawback in the past. Most printers years ago used daisy wheels or ribbons to print documents. The evolution of printer cartridges should be looked at.
How to Choose The Right Laptop Accessories?
The notebook computer is coming of age. For the first
time in history, notebooks or laptops are out-selling
their bigger cousins, desktop computers.
Which Notebook Computer Has Your Name On It?
Notebook Computers Are Sexy!
Digital Cameras, Media, and Card Readers
With the dropping prices on digital cameras and digital media in the past few years there is really a need for a quick reliable transfer method for your pictures to your personal computer.
An Inexpensive Solution to Securing Public Access Computers
Offering secure public Internet access is not as easy as it may seem. As the IT manager for a mid-sized public library, it's become apparent to me that creating a secure network of library workstations for use by the public is more important than ever before. System administrators have the responsibility of protecting the library's networks and systems, while ensuring quality and speedy service to all patrons. Offering public Internet access requires a dynamic security plan that is constantly under revision, taking into account the technical changes of the times. Traditionally, the software options available for help in this regard come at a significant price, often forcing libraries to spend thousands of dollars securing their computer rooms.
Just The Fax, M?am
For years, I smugly prided myself as a non-fax machine person. I felt it beneath my dignity to own such a technical contraption. The quill is more my style than a computer but, being practical, I reluctantly use a computer, casting wistful glances at the dust gathering on my quill.
Ink Cartridge Recycling 101
Let's take a moment to think about the topic of ink cartridge recycling. In our modern world we just keep throwing our trash away without sparing it a second thought. But where does all this left over trash go? It all goes to the local landfill polluting the land and water table. Is there anything we can do towards "saving the planet"? What if you could help save the planet and make some money doing it? It sounds too good to be
true doesn't it? Right now there are companies that will take away your empty ink cartridges and give you money in return!
7 Steps to Cleaning the Laser Toner From Your Laser Printer
Cleaning a laser printer, fax, or copier of laser toner can
be easy, provided you know what you're doing and use the
right tools. This article will share with you some simple
tips to help you clean your laser printers of laser toner
like a pro.
Can I Use My Old Ink With My New Printer?
The quick answer is...yes and no.
Ergonomic Products 101
Human beings are scaling new heights day by day. Markets are becoming more and more complex and competitive. Companies launch new products, market them, but even then are not sure if their product will match the taste, need and pocket of the consumer. This is because numerous brands are associated with a single commodity. Some companies try to win the consumer's heart via a low price while a few others offer an impeccable quality at significantly good amount. But at the end of the day what matters to the consumer is how the products minimizes the labor, enhances the work and its durability. This article will shed light on some of the eminent and world's top quality products called 'Ergo Products'. There are a wide variety of ergo products. They range from keyboards, mice, armchairs to keyboard stickers, footrests, foot switches etc. The ergo products one amongst the largely used ones nowadays . The reason being their consumer friendly nature and their troubleshooting strategy.
RFID for Beginners
RFID technology is used frequently today and has been around since the 1920s, but not many people know about, or understand it. RFID stands for Radio Frequency Identification and is used to store and retrieve information. This information is stored and retrieved using RFID tags or transponders. RFID tags are small and can be incorporated into many products. The tags have antennas that allow them to receive and respond to radio-frequency queries from an RFID transceiver.
Nvidia Geforce 7800 GTX Review
Nvidia has done it again, with it's newest video card, the geforce 7800 GTX. If money is no object and you demand the best, this is the video card for you.
|
